Washing Machine Smells Like Mildew: Causes and Solutions

A washing machine that smells like mildew is a common household problem, usually caused by trapped moisture, leftover detergent, and organic residue inside the drum and hoses. Front-load machines are especially prone to this issue because their airtight doors can prevent the interior from drying completely between loads. This guide explains where the odor comes from and how to eliminate it for good.

Left untreated, mildew buildup can transfer musty smells to clean clothes and shorten the lifespan of your appliance. The following sections cover the primary causes, step-by-step cleaning methods, and practical habits to keep your washer smelling fresh.

Common Causes of Mildew Smells

Detergent and Fabric Softener Residue

Using too much detergent or liquid fabric softener leaves behind a sticky film that traps dirt, body oils, and moisture. This residue provides an ideal breeding ground for mildew and bacteria, particularly in the detergent dispenser and around the door seal.

Trapped Moisture in Front-Load Machines

Front-load washers use less water and seal tightly during the cycle. When the door stays closed after a load finishes, moisture remains trapped inside the drum and gasket. Without airflow, mildew can begin growing within hours.

Wet Laundry Left in the Drum

Leaving damp clothes in the washer after the cycle ends gives mildew a direct food source and a warm, wet environment. Even a few hours of delay can create a noticeable sour or musty odor.

Clogged Drain Pump Filter

Small items, lint, and debris can collect in the drain pump filter. Standing water around trapped debris becomes stagnant and develops a mildew smell that recirculates through the machine.

Hard Water and Mineral Buildup

Mineral deposits from hard water can combine with soap scum inside the drum and hoses. This buildup creates rough surfaces where mildew and bacteria adhere more easily.

How to Remove Mildew Smells

Clean the Door Gasket

Pull back the rubber door seal on a front-load washer and wipe away visible mildew, soap scum, and debris. Use a mixture of equal parts white vinegar and warm water, or a mild bleach solution if the manufacturer permits it. Dry the gasket thoroughly with a clean towel afterward.

Run a Cleaning Cycle with Bleach or Washer Cleaner

Add chlorine bleach or a commercial washing machine cleaner to the dispenser or drum, then run the washer’s cleaning cycle or a normal hot-water cycle with no clothes. This kills mildew spores and flushes out residue from the drum and internal hoses.

Clean the Detergent Dispenser Drawer

Remove the detergent drawer completely and scrub it with warm, soapy water. Pay attention to the siphon tubes and corners where old detergent and fabric softener dry and accumulate. Rinse well before reinstalling.

Clear the Drain Pump Filter

Locate the drain pump filter, usually behind a small access panel at the front bottom of the machine. Place a shallow tray underneath to catch water, then unscrew and remove the filter. Clear out lint, hair, coins, and other debris, rinse it under running water, and replace it securely.

Wipe Down the Drum

After running a cleaning cycle, wipe the inside of the drum with a dry cloth to remove any remaining moisture. Pay special attention to the area around the door opening where water tends to pool.

Preventing Mildew Smells from Returning

Leave the Door Open Between Loads

After each wash, leave the washer door ajar so the drum and gasket can dry completely. This simple step prevents moisture from lingering and discourages mildew growth.

Remove Clothes Promptly

Transfer laundry to the dryer or hang it up as soon as the cycle finishes. Avoid letting damp clothes sit in the machine overnight or for extended periods.

Use the Correct Amount of Detergent

Measure detergent according to the load size and water hardness. High-efficiency washers require HE detergent, and using too much creates excess suds and residue that feed mildew.

Run a Monthly Cleaning Cycle

Run an empty hot-water cycle with washer cleaner or bleach once a month, or as recommended in your owner’s manual. Regular maintenance keeps residue and odors from building up.

Wipe the Gasket Weekly

A quick weekly wipe of the rubber door seal removes soap scum and standing water before mildew has a chance to form.

When to Call a Professional

If the mildew smell persists after thorough cleaning, the issue may be inside the drain hose, pump, or internal components that are not easily accessible. A technician can inspect for mold growth in areas you cannot reach and check for drainage problems that leave standing water in the machine.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *